Temperature Valve Actuator Replacement. Posted on sep 19, 2009 Failure to follow the correct procedure could cause air bag deployment, personal injury, or unnecessary sir system repairs.
Solenoid, High Temperature, 3Way Valve Hot Melt from www.hotmeltreplacementparts.com
You need to change drivers side temp door actuator then disconnect battery for 5 seconds and reconnect after changing the part, turn key on for 60 seconds with touching heater control to allow actuator to program and then it will work. Plan starts on the date of purchase. Install the instrument panel assembly.
Source: www.hotmeltreplacementparts.com
How does a temperature control valve work? 1.remove the instrument panel hush panel.
Source: bestsavingclick.com
15 psi m ax imum inlet steam: The actuator blend is designed to give a controlled volume change, hence known stroke response, within a narrow range of temperature variation.
Source: www.zip-corvette.com
The actuator recalibration procedure for the body control module must be performed after replacing the temperature valve actuator on the left side. Tighten screws to 1.9 n.m (17 lb in).
Source: www.ebay.com
The actuator blend is designed to give a controlled volume change, hence known stroke response, within a narrow range of temperature variation. Thermal actuators are the key operative components inside devices ranging from thermostats to valve products like thermal bypass valves, thermostatic mixing valves, tempering valves and thermostatic balancing valves.
Source: www.ebay.com
Allow a minimum of 45 seconds for the temperature valve actuator to move to the full hot position. Tighten 2.5 n·m (22 lb in) 2:
Source: www.amazon.com
Remove retaining screws from temperature valve actuator. Tighten 2.5 n·m (22 lb in) 2:
Source: www.go-parts.com
Inspect the temperature valve drive for cracks. 1.remove the instrument panel hush panel.
Source: www.ebay.com
When you are performing service on or near the sir components or the sir wiring, you must disable the sir system. Then remove the 4 screws that hold the upper glove box in place, then pull the glove box out.
Source: www.hotmeltreplacementparts.com
When you are performing service on or near the sir components or the sir wiring, you must disable the sir system. Remove retaining screws from temperature valve actuator.
Source: siristore.in
How does a temperature control valve work? Temperature valve actuator bolt (qty:
Source: 1factoryradio.com
Position the lh temperature valve electric actuator, then align the slots in the electric actuator driver to the flats on the lh temperature valve shaft. Before getting into the working of the temperature control valve, it is important to understand its structure.
Source: www.amazon.com
Electrical connectors to the instrument panel compartment lamp and switch assembly. Refer to battery negative cable disconnection and connection.
Source: www.amazon.com
But this video shows you where it is located as well as how it is supposed to work. Allow a minimum of 45 seconds for the temperature valve actuator to move to the full hot position.
Source: nabiswa.com
Inspect the temperature valve drive for cracks. Refer to temperature valve actuator replacement in si.
Source: sdparts.com
Then remove the 4 screws that hold the upper glove box in place, then pull the glove box out. Snap the temperature valve link rod into the temperature valve.
Source: www.amazon.com
But this video shows you where it is located as well as how it is supposed to work. This is what it looks like with the temp valve actuator removed.
Source: safarani.com
Install the instrument panel assembly. Before getting into the working of the temperature control valve, it is important to understand its structure.
Source: www.carid.com
Refer to instrument panel sound insulator replacement in interior trim. Remove the four 7mm bolts from beneath the glove box.
Source: pcjacht.nl
When you are performing service on or near the sir components or the sir wiring, you must disable the sir system. 4585850 if the temperature valve is cracked in more than one place or has a piece missing, proceed to step 5.
Source: horsesean.blogspot.com
How does a temperature control valve work? Temperature valve actuator retaining screws.
Media Temp Range 60°F To 266°F [15.6°C To 130°C] Water Max 250°F (120°C) Steam Maximum Differential Pressure (Δp) 60 Psi T Ypical Applicatio N 116 Psi Full Open Only (Model # B215Ht455 ) Steam:
Refer to disabling the sir system. Remove the four 7mm bolts from beneath the glove box. This is what it looks like with the temp valve actuator removed.
Temperature Control Valves Are Distinguished Based On The Number Of Ports They Have.
Remove the temperature valve actuator. 4585850 if the temperature valve is cracked in more than one place or has a piece missing, proceed to step 5. Then remove the 4 screws that hold the upper glove box in place, then pull the glove box out.
Refer To Battery Negative Cable Disconnection And Connection.
Tighten screws to 1.9 n.m (17 lb in). Thermal actuators are the key operative components inside devices ranging from thermostats to valve products like thermal bypass valves, thermostatic mixing valves, tempering valves and thermostatic balancing valves. Step 1 :removing the air temperature door actuator.
Tighten 2.5 N·m (22 Lb In) 2:
Genuine gm 52474810 a/c temperature valve actuator : Identifying electrical connectors courtesy of general motors company 2.disconnect the electrical connector. This is the temp valve actuator after the removal and replacement.
Slide The Electric Actuator Driver Onto The Shaft, While Aligning The Actuator Locating Hole To The Forward Alignment Pin On The Hvac Module Case.
Electrical connectors to the instrument panel compartment lamp and switch assembly. Before getting into the working of the temperature control valve, it is important to understand its structure. The actuator recalibration procedure for the body control module must be performed after replacing the temperature valve actuator on the left side.